Tip 1: How outweigh door refrigerator Indesit

Door Refrigerator "Indesit" is usually hung on the right side.If the layout of the room does not allow to open the door at the right hitch, it is necessary to outweigh.Almost every modern manufacturer, producing refrigerators, lets do it.
you need
  • - screwdriver (ordinary and curly).
Guide
1
Make sure that the door of your refrigerator can be rearranged.Inspect the refrigerator.You must find the plastic plugs, which are designed for fastening of the handle, and the rotary hinge, located on the door.The main body of the refrigerator should also be attachment.
2
Unplug the refrigerator from the power to protect yourself from electrical shock.
3
empty the refrigerator and remove all food shelves.
4
Remove the door handle.
5
Remove the caps from the door, using a flathead screwdriver.
6
Remove from the refrigerator fastening, holding the door.
7
Carefully remove the refrigerator door.
8
Remove the door by turning the loop.On the opposite side o
f the door, remove the plug holes for the hinges.
9
Screw the hinges to the opposite side of the door mirror of the previous position.
10
find plugs for turning loops on the left side of the refrigerator.Take them out, then move the hole in the right side, which have been used previously.
11
Put the door to the refrigerator and screw hinges.Adjust it if necessary.

Tip 2: How to outweigh the door

happens that the door to the apartment is hung so that when you open a window blocking, and you're looking at a blank wall displeasure.Of course, much would be better if the open door you will see a window.However, there are other cases where it is appropriate to outweigh the door so that it does not open inwards and outwards.
How to outweigh the door
you need
  • screwdrivers, knife, metal ruler, a chisel, a mallet, a hammer with a thin striker, plane, thin metal nails, carpenter's glue, putty for wood
Guide
1
For pereveshivaniya door you need to move the locking latch plate, to make a new nest for loops in the box and in the very doors , and patch up the old nest.If you intend to change the direction of the door opening , then you need to move a door stop, and even rearrange the handle.It is possible that the door will have to repaint.
2
Remove the door from its hinges.To do this, open it and insert the bottom wedges.Remove the screws from the bottom hinge.Then do the same with the top loop, leaving one screw.You need assistant who will hold the door while you are removing the last screw.Carefully remove the hinges from their slots.Old nests can be repaired.
3
Now put the door on the mock timber and secure it.Mark the position of the loop on the end of a knife on a metal ruler.On the front side door mark the depth of the new nests.Do the cuts across the end to the desired depth.
4
with a chisel cut a new nest.Attach the loop to the future site of attachment and mark its position.The rest of the piece of wood, close the slot.Grease glue wooden plate and insert into the slot.Nail plate thin nails.Allow the glue to dry time, then ostrogannoj site and install the loop.
5
rotate the door latch so that the bevel fell on the stopper plate.Secure the door to the bar.Door handles and knobs on the front part will have to be removed.Remove the latch from the hole, and then expand to 180 degrees.Insert the hook into the hole and attach trim screws.Now you can mount the door handles.
6
With the door frame, disconnect the stopper plate and plate cut from a tree the size of the hole.The plate glue in place, and when the glue is dry, the gaps zashpatlyuyte.Irregularities cut off with a chisel and plane.
7
Install door vertically to heel bar at right angles to the door frame.Secure the door wedges.Mark the places for hinges on the door frame.Along the lines of markup spend a knife, and select the slot, and then cut the slot.
8
Hang the door, close it and make a mark on the front side at the point where there will be a latch.Apply Label stopper plate and drag it along the contour of the knife.Drill, chisel and then follow the holes for the tongue.Cut a slot for the lock plate and fasten it in place with screws.
9
Palm door tear chisel, close the door and mark the new position for the stop on the door frame.Grab the emphasis on the new place, set it level and final nail in all places.
Note
for reweighing doors of some models of refrigerators "Indesit" requires additional parts.For example, sometimes we need different loops.They are included with the device.Before you begin reinstalling, refer to the instruction manual of the refrigerator and make sure that these parts.
Helpful Hint
Some models of refrigerators after reweighing require you to reinstall the sensor opening the door.This is indicated in the instruction manual.To reset the sensor has a special mounting holes formed on the opposite side.
Sources:
  • Perenaveska refrigerator door
  • perenaveska refrigerator door

0
0