Tip 1: How oblitsevat tiled stove

Ceramic tile is very well suited for finishing stoves.This tile can make the oven aesthetics.After finishing there will increase the heat capacity of the furnace.If the styling is made properly, the tiles will be kept on the stove for many years.
Guide
1
First you need to start preparing the oven for laying tiles.Clean it entirely from clay, old paint, liquor and anything that might hinder the smooth tiling.Clean up is necessary to clean bricks.Pay more attention to the seams.They must be cleaned to a depth of 1 centimeter.Professional builders clean the oven with a wire brush or grinder with a special nozzle.Often, problems arise with the removal of old paint.In this case, make a small incision on the entire surface of the furnace.The depth of cuts should be about 3 millimeters.Finalizing the furnace to be laying by wiping the surface with a damp sponge.
2
After that, the furnace secure special masonry grid, which has a cell size of 50x50 and a diameter of 0.5-1 mm.For this purpose it i
s possible to use metal anchors.Also suitable conventional screws.They need to be screwed into the pre-drilled holes pobeditovym drill.Quite often, the mesh is attached to the master embedded in pieces of wire sutures.They should be placed at a distance of about 15 centimeters.
3
for laying tiles on the stove is suitable or conventional heat-resistant tile adhesive.Among the experts is very popular adhesive mortar SCANMIX «Skanfixsuper».It is specifically designed for lining the furnace with ceramic tiles.Available in the form of dry mix.It is best to add to the adhesive solution, common salt in a proportion of 1 kg of salt on one bucket adhesive.This is done to keep the water in the adhesive solution.Salt will prevent its evaporation and adhesive mortar normally take effect.
4
laying ceramic tiles must be carried out on a heated to a maximum temperature furnace.This temperature must be maintained at all times styling.Lay tile is best below.To sutures were identical, you can use crosses.Every few rows should be checked vertical masonry.It should immediately correct laying, if necessary, as then it will be impossible to do.

Tip 2: How to Lose

stove oven in most cases is located in the house and is a part of the interior.After laying it looks not very aesthetically pleasing.Its rough part is very difficult to keep clean.To create a good appearance is necessary to use finishing materials.
How to decorate the stove
Guide
1
surface of the oven may be simply plastered.Perform this work only after final drying of masonry.To start you need to clean the surface of the clay.Then you can move on to clearing the seams.These actions are carried out to ensure that the plaster is well stuck to the wall.You can also use a metal mesh.She fastened it to the surface of the furnace twin wires that are laid in advance joints.Their ends must be located at a distance of 8 cm from each other.
2
Before plastering necessarily good to heat the oven.Hot surface, moisten with water and apply it to the solution of two layers.The first layer should have the consistency of sour cream.The second layer must be thicker.The average thickness of the layers should be 6-8 mm.If the surface is uneven, the layer thickness can be increased to 10 mm.After applying plaster solution can proceed to the leveling and smoothing of the surface.
3
Dry components of the solution need to sift through a sieve.Thereafter, in a dry form should be mixed sand, cement and asbestos.Add this mixture to a solution of lime.If you decide to use as gypsum, it dissolve separately, then combine with lime mortar.To strengthen the plaster, you can add a little salt to the solution.In 10 liters of solution will be enough of 300-400
4
To decorate the plastered surface can be used rustication.Rust is a shallow groove.They can be applied on the surface of the plaster using grouting.First you need to identify future geometric pattern.After this line of cut and jointing rusty.After the grooves are cut, you can paint the oven.Grooves often painted white and the surface of any other geometric shapes.
Note
for lining fireplaces and stoves can be used or clinker floor tiles, square or rectangular shape, any size, thickness not exceeding 6 mm.Tiles must have high heat-resistant qualities and have a glazed front surface.When the joints to dry cloth to polish the tiles.
Helpful Hint
First of all, you need to prepare for laying the oven.To do this, you need to clear it from clay, paint, mortar and anything else that will not interfere with installation of ceramic tiles.Clean the oven until you need to clean bricks.The seams must be clear to a depth of at least 1 cm. Experts recommend to clean the oven with a wire brush or grinder with a special nozzle.
Sources:
  • how and what oblitsevat oven

0
0