you need
  • mounting bracket
  • fabric pattern (veil)
  • pattern paper
  • Threads,
  • Scissors
  • Mel
  • pins
  • main fabric
Guide
1
process of creating patterns SMAD starts with buying the working material for the construction of the template.Because of the veil you do a test model that will form the folds.Then you can move to the final version of the fabric from which plan to sew.
2
base pattern equilateral SMAD is an isosceles trapezoid.You need to draw half a trapezoid.Measure the height of the future SMAD.Pelmets windows in the model homes rarely sew height of more than 50 and less than 30 cm. Take the approximate height of 45 cm. Since the SMAD is semicircular with a clearly laid folds, this height we multiply by a factor of folds, which is equal to three.Thus, 45 cm x 3 = 135 cm. Height our trapezoid.
3
Next is half the value of the upper perekidy, or ½ the upper side of the trapezoid.Look at your window, imagine how much SMAD you need to decorate it, and about how to be the distance between the folds of each SMAD.At a height of 45-50 cm SMAD, more organic look perekidy top width of 30 cm. So, AB = 30 cm.
4
The next point is the depth of the pattern on the first fold.This value is also taken arbitrarily, it is 5-7 cm. Note the drawing point A1.Now you need to move the overall height of the SMAD to a depth of the first fold.Put the point B1.
5
then determine the length of sagging SMAD.Take the cord and simulate using a dangling lower edge of the SMAD.Simply attach the ends of the cord to the mounting bracket.The deepest point of the slack cord must be equal to 45cm.Remember, you are modeling a SMAD, and do so in accordance with your taste.Measure the length of the cord that hung between two pins.Divide it in half.
6
Spend from point B perpendicular.Put it on a segment equal to half the length of the cord, and you get the point G. Connect the dots B1 and D smooth semicircular line.You've got to figure 4 basic points, shaping the future pattern: A1, B1, G, B. Connect the dots B and G. Before you half of the paper pattern.
7
To SMAD well draped, it cuts out on the bias.Fold bought otrez veil at an angle of 45 degrees.Pin the pattern, positioning the segment A1B1 Bend tissue.Add 1 - 1.5 cm at the seams, and carve out the right part.Mark the middle of the fabric pattern.
8
Make a mark on the mounting plate.Draw a straight line perpendicular to the bottom.Along this line, you will target mid-SMAD, to avoid distortions.

Fix the mounting plate to the upper perekidy three pins, combining with the middle mark on the mounting plate.The last slide pins, retreating 7-9 cm from the edge of the fabric.Lay the first fold and secure it with pins on both sides.Align the fold hands, pay attention to the middle of the crease was just above the vertical line that you held.In the same way is folded along the entire length of the shoulder, fastened together with pins.The approximate depth of each fold - 5-7 cm. Try to keep the folds were equal.
9
retreated a couple of steps to determine which arm you got better.Sew small stitches to fold it over once pins.Stepping back from the seam by 2 - 2.5 cm, cut the excess fabric.Remove the template from the mounting board.Remove the pins and Basting stitches.Fold the fabric along the center line and cut the second arm so that the pattern was completely symmetrical.Unfold the fabric and iron it iron.Before you finished pattern template equilateral SMAD.Using it, you carve out SMAD as much as you planned in the model pelmet.Now you can calculate how much fabric you need, and go to the store.
How to carve SMAD