Tip 1: How to change the plug from the headphone

«eternal" headphones, alas, does not happen.Even if they are very expensive, sooner or later they will break the cable.Most often it occurs near the plug.Change due to a malfunction of the headphones entirely inappropriate as how to change the cell phone because of deterioration of the battery.
Guide
1
sure to place the cliff is located in the connector.If it is located even in a couple of centimeters from him, better to repair the open in a string, you replace the plug.To determine the break slightly sway cables at different locations.
2
Before repairs disconnect the headphones from the device.
3
Obtain a plug for headphones.It must be of the same standard as that of an existing fault (stereo, Jack).Mono does not fit.New plug, unlike the old, has a folding design.Note that the new plug must also have a diameter similar to the same parameter of an old (6.3 or 3.5 mm).
4
alternative to purchasing a new plug is to use the appropriate items from other headphones.Find among you
r existing headphones are defective, which is not open in the plug, and elsewhere.Cut them short (length of about four centimeters) piece of cable with plug.
5
If a new plug, cut off the old, then remove with a new cap.Thread the cable through it, and through a small piece of the insulating tube.Solder the two colorless or yellow wires to the rack.Blue or green wire is soldered to one of the small contacts, orange or red - to another, as previously put on them the pieces of the tube even smaller.Then, pull the pieces on the tube soldering.A large piece of pipe to move closer to the front, and then through the cable clamp available on her legs.Do not apply excessive force in this case.Screw the cap back onto the plug.
6
If a tip from other headphones, connect all yellow or colorless wire both cords together.Separately connect the blue (green) wire to the other wire in the same cable.Also entered and red (orange) wires.Securely isolate the compound, including, and from each other.
7
Connect your headphones to the device and check.

Tip 2: How to connect the headset to plug

There are several types of connectors: straight, angled and original molded.When selecting plugs to consider the characteristics of each species.For example, straight plug is easily pulled out of the player and puts a heavy load on the plastic socket of the receiver.Corner is also not sufficiently firmly seated in the player.
How do I connect the headphones to the plug
Guide
1
Turn on the player and bending wire, make sure that the break occurs near the plug.Then, with a small margin in the right place, cut the cable.You will need a small piece of transparent silicone tube (you can use the handset from the dropper).Thread the cable into the phone in advance.
2
Cut with a sharp knife plastic plug head and bare metal part of the plug.
3
prepares the cable with a sharp knife or a soldering iron, separating all the components of the wire.Then twist the appropriate cable wires and tin.For tinning the most budget lacquered wires, use aspirin.In no case were intact varnish with a knife, because it cuts the wires lead to premature fracture.
4
Solder the cable to the connector , observing the correct pinout.During phasing headphones just make sure which wires go to some headphones.If the fork goes round cable or passes through one headset to another rung cable tester or by the player.If the cable is a different color, the red color is usually marked by the right channel, and white - left, but it happens and vice versa.If you have a solid conductors, the common wire will be the conductors that are not varnished.But in any case it will be safer to ring cable tester before soldering.
5
Connect the connector to the wire.Moreover, the wire should be inside the silicone tube.That is, the connector extends perpendicularly through the tube.Fill the space between the sealing plug and the tube and tighten the remaining end of the tube with a paper clip or slinging type "crocodile".Once captured and sealant harden (20-30 minutes), wrap the edge of the pipe thread.Cut off excess tubing.Then cover everything again sealant, and an hour later the headphones are ready to use.
Sources:
  • how to connect two earphones
Sources:
  • how to replace the headphones

0
0