Tip 1: How to connect an electric oven

typical electric oven is connected to the home electrical network via a three- or four-wire connection.Since the oven is a powerful consumer of electric current, it is important to organize the installation of sockets and wiring to it.
you need
  • - screwdriver;
  • - electrical tape;
  • - three - or four-pin connector;
  • - three-prong outlet with earth;
  • - copper wire 4 mm2;
  • - circuit breaker 32 A.
Guide
1
Carefully read the instructions and learn limiting the power consumption of the oven.Then select a suitable power socket and fuse machine (with a power consumption of about 6 kW current limit is about 32 A).
2
Set standard Euro-socket with protective earth contact rated for 32 A, close to the intended location of the oven and connect elektoseti apartment through a separate line.It is best to use three-core copper wire 4 mm2 and an automatic fuse 40 A.
3
Remove the metal shield on the rear side of the oven, you will see three wires (red, white, and black).On plates with a four
adapters, there is also the green wire, which is connected to ground.
4
Connect the colored wires to the connector terminal adapter.Pass the cord through the bottom opening so that the installation of a protective shield does not interfere further manipulation.The colors correspond to the colors of wires cable wire connector: red and black - AC, white and green - land.Screw the wires to the connector, make sure that all connections are tight and wrap them with tape if the joints are not far apart.
5
Screw the protective metal plate in place.
6
Set the oven, leaving about 10 cm between the device and the wall.
7
Turn on the power plug.If the current is turned on, the oven should work.Check out all the functions of the oven, make sure that they work properly.

Tip 2: How to connect Electroovens

Modern electric ovens are pretty sophisticated equipment.Unauthorized connection ovens is only possible if you are a qualified electrician.Improper installation and connection of electric oven may result in a complete failure.
How to connect Electroovens
you need
  • - building level;
  • - Screwdriver;
  • - plug.
Guide
1
Inspect and check Electroovens .If you find any damage caused during transport - you can not connect the cabinet.
2
vyverte niche carefully designed to install electric oven, using a builder's level.It is unacceptable to set the oven on an uneven surface, as this will lead to a misalignment of the cabinet and, consequently, to the misallocation of heat and problems in the oven.
Make sure that between the rear panel and the floor of the niche there is a gap, intended for ventilation.The size of this gap should be at least 85 mm.
minimum clearance between the walls of the electric oven and the internal walls of the niche must be at least 5 mm on each side.The minimum clearance between the back wall of the oven and the recess must be at least 30 mm.
3
Make sure the voltage and frequency of your power supply meet the requirements of the installation of the device.For this study the nameplate electric oven.Equip cord instrument plug withstand the loads specified on the label.
If the oven is connected to the network without the use of plug must be installed disconnect device, to the breaking poles.The measure provides for the requirements of technical safety.Using a flathead screwdriver, open the back cover at the bottom of the oven.Remove the screw connection and cable clamp.Connect the wires to the appropriate terminals.At the same time, the ground wire should be connected to the terminal Electroovens
4
Carefully place the oven in a niche.When installing the cabinet, use special transport handle.It is unacceptable to use the oven door as a lever.
5
Attach the oven to furniture with screws and mounting washers supplied.
6
Remove any protective film used for transporting the device
Note
Before starting work, disconnect the electric power.


Manufacturers ovens strongly recommend the installation of ovens trusted only to professionals.


Oven must be connected to an effective earthing system.
Helpful Hint
Make sure the socket used to connect the electric oven, there was easily accessible after installing the device.
Sources:
  • plant -izgotovitelya instructions for installation and operation of electric ovens.
  • independent activation of the oven
Note
sure to turn off the electricity before starting work.
Try to avoid a situation where for the oven passes gas strut as the oven may be very hot, and gas pipes for safety can not be packed in heat-insulating materials.
Make sure the socket for connecting electric oven remains easily accessible after installation.
Helpful Hint
When planning the kitchen, leave extra 5-8 cm on each side, as the oven is usually heated strongly enough, even though the system provided heat and ventilation
Sources:
  • Installation Instructionsand setting up electric ovens.

0
0