- Electric drill, screws, pipe clamps, air
products on the market - an abundance of different models.But first, select the ones that suit you in size plates (eg 60cm x 60cm for four camphor gas stove).Of these, pick the model that suits you in color and shape to the design of the kitchen.Ask integrated functions and power of future acquisitions.
choice is made, an extract taken home.Check the integrity, the turbine and the backlight.Everything is OK, it's time to be taken for the installation.As a rule, all current models can be used in the recirculation of air (through a carbon filter), and for the forced removal of fumes and
odors and smoke through the ventilation system.Selecting the operating mode by simply rotating the hood switch.The most efficient extractor can be operated only if the house has a quality ventilation system.
The first step is to secure the hood on the wall.Mark up space for mounting such a manner that the distance from the slab surface before stretching was not less than 75cm.When using a drill, special plugs and 4 screws securing hood on the wall of the intended line.Carbon filters are installed by default and do not require further action.For them, the installation is complete.If you are going to use a system of forced ventilation, carbon filters remove, and use them only when necessary.
When you connect the hood to the ventilation system, before it is mounted on a wall Place the cover in the hole in the body, which will not be used.On another hole, which will connect the corrugated hose, install the plastic cylinder with check valve.He made the cut in the form of a circle with fastening halves on the axes.When the turbine halves rise under the influence of air flow, and when turned off, under its own weight, will fall into place and will cut the external network.This is in order to protect the room from drafts and dust.On the plastic cylinder with check valve fasten corrugated aluminum pipe and fasten his collar.The other end of the hose is attached to the same way pre-assembled duct.The duct is made of pipes with a diameter slightly less than the diameter of the corrugated hose and attached to the wall brackets or special long screws.Connecting the air vent directly to the well can be done with the L-shaped pipe, which is set in the well bore and sealed plaster solution.
hood Connect to an electrical outlet.Socket (grounded), it is desirable to set in close proximity to extract and use only for her.Here everything is ready to go.Clean air you!
Tip 2: How to mount the hood
Hood is very much needed in the kitchen, as the ability to clean the air.It prevents the spread of indoor odors, fumes, and air pollution.Also, thanks to drawing furniture is not covered by a disgusting fat bloom.Select hood can be to your taste.The lineup of the representative of a class of air cleaners will appreciate its diversity.
- hoods, ducts, tape measure, level, drill, dowels, screws, hammer, construction pencil, hammer, drill on concrete for punch (SDS +).
If you connect the duct to a common ventilation duct with its neighbors, the smell of cooking will be returned to you, or to go straight - to the neighbors, becauseMine could miss 2-5 times less air than banish your hood.In this case, it can not be cleaned, continuing to absorb air pollution.Alternative connecting duct to the total ventshahte - concluded the street.Having secured agreement with the local authorities, cut through a hole in the wall.Use for this purpose punch by setting concrete drill bit.
When buying hoods note on completing the duct.Their diameter must match the cross section of the ventilation shaft of the room.The duct should not be strongly bent too long.Umbrella hoods should be not less than the width of the cooking surface to remove odors as efficiently as possible.
For hoods should have a separate outlet.Install it needs during repairs in the kitchen.If this socket has not been previously mounted, is establishing a new, put the wires in the cable channel.
Arm level and a tape measure and make markup.Apply construction pencil mark where the hood will be attached.From drawing up the hob should not be menee70 see, and to a gas cooker - 80 cm.
drill or a hammer drill at the marked locations dowel holes.Hammer anchors with a hammer, tighten the bolts on the wall support.In support install hood.The casing is not put on.With adjusting bolt, adjust the position of the hood.It should be installed horizontally.
Now connect the duct to the vent.If the vent is located opposite or on a fairly large distance from the plate, route it to the extra boxes.It is advisable to hide them on the mounted cupboards.All joints are sealed.
After installation, set the ducts and exhaust hood and fix it by adjusting the height.Make a trial run, by connecting the appliance to the mains.
The kit includes contemporary drawing tehprovodnoy cord, connect the hood through its strictly according to the scheme.
- extractor fan in the kitchen how to install