Tip 1: How to put a tile on plywood

modern construction technology allow oblitsevat any surface: concrete, wood, brick.Put the tiles can be on ordinary plywood, which today are not infrequently used for covering walls, ceilings, floors, interior walls at the device.
you need
  • - tools for grinding;
  • - elastic adhesive;
  • - waterproofing;
  • - ground;
  • - wood screws;
  • - Roulette;
  • - tic tile;
  • - solution for grouting.
Guide
1
Measure the thickness of the veneer layer and the base.Walls and floors are lined with ceramic tiles are heavy, so not every surface withstand high loads, which will lead to its deformation.The very same tiles will not keep.Experts recommend that the thickness of the plywood base has been not less than 28 mm.By European standards, the thickness of each sheet of plywood - 22 mm and more.
2
Inspect the strength of the plywood base.The coating must be immobilized, otherwise the quality of work will suffer.If necessary, secure good plywood sheets to the wooden base.
3
Thoroughly clean the surface
for subsequent coatings.This rule is always when laying tile, regardless of the type of foundation (concrete, wood, brick, etc.).Use abrasive and grinding tools.Sand is necessary so that the upper layer of the veneer was flat, without roughness and other deformations.
4
Before we put the tiles on the plywood, cut the surface of the ground.Basic treatment consists of two layers, each layer should be thoroughly dry, it takes, on average, five hours.The bathroom plywood sheets must be pre-treated with a waterproofing solution.
5
Place the first tile in any corner where according to preliminary estimates should be seamless tile.Use a level to obtain flat ranks.Evenly spread the glue on the surface, attach it to the tile and press firmly in her hand.Within a few minutes until the solution hardens, you can adjust the position of the tiles on the floor or wall.
6
between two adjacent tiles attach special crosses - it is necessary to size sutures were identical.The average seam thickness of 2-3 mm, but in areas which are characterized by sudden changes in temperature, thermal seam is required, ie the distance between the tiles should slightly increase - up to 5 mm.
7
Seal grout joints special.Typically, such work is performed on the third day after laying tiles when she grabs the surface thoroughly.Rubber knife evenly by means of the seam, remove any excess solution.Give the seams dry for 20-30 minutes, then wipe the tiles with a damp cloth.After a few hours of treat lined with a dry sponge.

Tip 2: How to glue tiles on the plywood

Currently, the increasing popularity won the carcass construction technology, provides for laying floor tiles on a special plywood , has a high degree of water resistance.
How to glue tiles on plywood
you need
  • - ceramic tiles;
  • - two-component elastic adhesive;
  • - anchor;
  • - plywood;
  • - primer;
  • - grout;
  • - measuring device;
  • - chalk;
  • - cloth.
Guide
1
Prepare the surface: the exposed joists lay special plywood and screw it to the screed anchors.There is one important caveat: the step that must fit joists should be about forty centimeters.The thickness of the plywood should be equal to thirty millimeters (with a smaller thickness of the plywood surface is tough and durable enough, and therefore, tiles will become flaky and crack).
2
Follow the floor layout.To do this, locate the center of the longest wall of the room and draw from it at right angles to the line connecting the wall opposite.Spend a similar operation, connecting the walls smaller.That will have two intersecting at right angles to the line.
3
find the starting point: in some cases, the line shifted somewhat, minimizing thereby trimming.Avoid that ceramic tile has been trimmed on all sides, as the room will not look nice.
4
Prime with the surface and let it dry out a bit.
5
Apply two-component elastic adhesive on a small area of ​​the floor surface.Apply glue to the back of each tile and stick tile gradually one after the other, moving from the reference point in the right direction. pasting tiles , just held her to the floor.
6
Allow to dry and the tile joints powertrowel special grout that will significantly extend the service life of the tile.Wipe off any excess grout before it dries. tile polish dry with a soft cloth.
Note
Always check that the tile has been laid out at the same level (otherwise the floor will be ugly swings).
Helpful Hint
to the distance between the ceramic tiles were the same, use the special delimiter (often called "cross").
Sources:
  • than sticking to the plywood tiles
Note
To ensure good quality of the hitch using high-quality adhesive for a particular type of tile.When buying a universal adhesive is carefully read the instructions for use, which lists the types of surfaces for which it can be applied.
Helpful Hint
Begin laying the tiles from the second row, regardless of wall or floor veneered.Such an approach would lay perfectly straight first row: if required the tiles can be cut to an optimal size.
Sources:
  • Topical issues of self-repair apartments
  • can lay tile on plywood

0
0