Tip 1: How to prepare the wall for painting

One labor-intensive processes in the repair work is to prepare the wall for painting.To cope with this task, you must have some skills builder.Prepare the walls for painting difficult.
you need
  • - spatula
  • - rollers
  • - cuvette
  • - putty
  • - primer
  • - fiberglass
  • - bucket filler
Guide
1
To start
strip the walls of the previous coverage.If you have wallpaper, moisten and remove them.If the walls were whitewashed, then wash it off with warm water.But if there was an oil-based paint, then here it will be more serious.Try to clean up the former base of the wall painting, that is before the panel or plaster.You can do it with a spatula, and if the paint does not give in, then try to do a hatchet or chisel.In any case, carefully smooth out the surface of the walls.
2
Once you have freed the walls of the old paint proceed to repair the walls.Defects are such as: crack, fall off plaster, or even worse, the fungus on the walls.
3
If there are cracks in the wall, then penetrate the
m deeply, then prime with.If the cracks are not deep, the zashpaklyuyte their basic filler, and if the crack is very deep, then repaint them with a solution.It so happens that the plaster layer of moving away from the wall with paint or wallpaper.Do not disregard these problems.Take a hammer and knock the plaster to the base of the wall, and place chips and prime the zashtukaturte.
4
fungus on the walls of a frequent guest on the first floor.Take special composition for the fungus and apply it with a brush, trying to rub the walls.This will help you in the future to get rid of this trouble.If the walls are still some flaws that you see, try to remove them to the finish putty.
5
next stage of your work will be to wash the walls.You saw that the walls were repaired - all cracks, holes, chips are embedded.Then proceed to the primer across the surface of the walls acrylic primer, since it is applicable to all types of surfaces.Take the foam roller, dip it in the cuvette (special container for paint) with soil and squeeze it.Now apply primer to the wall from the bottom up, and do not rush.Try to keep all parts of the walls were primed.
6
To walls were subsequently free of cracks, they glued a special fiberglass.This coating is strong enough, it is not torn, is held firmly on the wall.Paste it glue for vinyl wallpaper and smooth special spatula.Spread glue on the box as it is written and let it stand for a while.Next, take a cushion and glue smear wall.Cut the fiberglass, which will be equal to the height of the wall, and stick it, smoothing from the center to the edges.Next attach the web to the previous lap and trowel cut through both the web.You can do it, that both paintings hang butt joint.When you all walls are covered with canvas, then once again go over them with glue.Do this in order not to apply the primer.
7
Now it is time to finish putty.As it is carried out with glass of 2 times, technology is finishing.The finish coat is performed on the "stripping".Putty, apply a thin layer on the wall a large spatula and excess putty with a spatula remove the second smaller.Apply the plaster evenly.
8
After the plaster dries, it proshkurte fine mesh, which can be bought in DIY stores.Do not push strongly on the wall, to avoid scratches.And the last thing you should do is once again primed the walls.Now they are ready for painting.

Tip 2: How to prepare the wall for painting

Painting walls - the most common form of decorative treatment.With the advent of new technologies in Russia, it is becoming increasingly popular.Before applying the paint wall must be properly processed and prepared so that the coating is flat, beautiful and looked for a long time kept on the surface of the walls.
How to prepare the wall for painting
Guide
1
paint does not hide the cracks and irregularities, so the wall must be carefully aligned and treat small skin.
2
fresh plaster painting impossible.It must dry completely.Then cover it with primer 2-3 times, after drying, primer, you can start coloring.Well proven antibacterial acrylic primer.It is used for internal and external works and is safe.It can be used on the surface of the brick, concrete, wood, plasterboard.This primer is not diluted with water and applied to the surface in any way.Dried for 12 hours.
3
Internal wall , after preparation, dye water-based paint.It is presented in a wide range and has different colors.
4
If the wall has been painted previously, the old layer of paint must be removed, the surface is sanded fine sandpaper, using a grinder, cover with primer and paint.
5
outer wall , well-crafted from old paint and sand.
6
When painting wooden walls for the first time, before applying oil or acetone paint, linseed oil to coat the surface twice.Once dry, you can paint it.
7
When first applying water-based paints, prime with the surface as described above and apply vodoemulsionku.
Helpful Hint
to prepare the wall for painting, fiberglass, plaster

0
0