Tip 1: How to trim the plinth in the corner

final stage of interior decorating the room is a sticker baseboards .This is no big deal.Problems can arise with the angles in which you want to paste the plinth.That is why you need to know how to properly cut.
Guide
1
you can pretty easy to solve the problems.It is only necessary to make a washed down at 45 degrees adjacent baseboards .However, problems may arise.The fact that the rare perfectly flat floor.As a result, baseboards are in places fit different heights.For a snug fit, it is possible to file a little plinth.Corner moldings also needs to fit.Once you have made smooth plinth height, they can be nailed to the wall.
2
Quite often problems that are associated with gaps at the joints baseboards in the corners.The fact that the plinth is rarely performed after washed down a perfect angle.They need to be customized.
3
Before you install the plinth in the corner, grind their sharp ends.Thus, you compensate the radius of the inside corner.Otherwise the gap may have to be e
ven greater.
4
gap appears mainly due to the fact that the walls are not flat and smooth surface.In most cases, problems occur because of the lack of parallelism and squareness angles.That is, this leads to difficulties in finishing.
5
If the room has a small area, the data is not significant disadvantages.However, if the room is big, it will be very noticeable flaws.Almost all of the masters decide such problems using fillers.Putty, of course, possible, but still after some time there was a crack on the ground overlay.
6
The best solution is a good fit baseboards at the interface.
With a good fit, a place where baseboards always has a shutdown.Sometimes, even when a certain angle of view, the joint is hard to notice.You can always cover up your omission of putty.Try to avoid it.Before you start customizing the plinth, carefully choose which one you'll be treated.Look at the corner of the room to the point where most people will be.The joint must be visible.

Tip 2: How to cut skirting

To give a complete image of the room is often used ceiling moldings (baguette).His installation - is simple enough, but the difficulties begin with the first angle, and more precisely, to attempt to correct cut plinth for docking.
How to cut the plinth
you need
  • - plinth,
  • - Stationery knife,
  • - miter box.
Guide
1
Immediately it should be noted that for the installation of the product, you can buy ready-made corners that can be sold complete with plinth th.But what if you did not have the right parts in stock?In such a situation will help a special device - miter box.This is a handy template to control the cutting line on the ends plinth and .Mitre box has several grooves, each of which corresponds to a specific angle.The plinth is applied to the tool, and then cut at the desired angle.For cutting use office building or a knife, with the blade must be sharp enough.Otherwise, the edges of the plinth and appear jagged.
2
should be noted that use of the miter box is not always possible - it is designed for the standard angles, and in most corners of the homes may differ from the figure of 90 degrees.Moreover, many buildings have more than four room walls.There will only fit hand-cutting.
3
stykuya plinth in the corner, you need to mow the ends of both bands, so that eventually get a turn about 90 degrees.The complexity of cutting and joining is that has to be oriented in three planes: two perpendicular walls and ceiling.To order, for example, the inner corner, you need two baguette, pencil and ruler.
4
Attach the first baguette close to the corner so that it rests on the perpendicular wall.Second baguette Abut the first on the other side of the angle.
5
On the top edge of the first baguette make a notch in the place where rests the second prints.The difference with the external angle that is necessary to make a notch on the lower edge.
6
Subtract from the wall labeled plinth .On its reverse side with a pencil and a ruler to connect the place serifs and bottom corner.The result should be a kind of triangle that you cut.The same procedure should be done with a second baguette.
7
cut edge, try on again baguettes to each other in the corner.If you see a gap, the edge of the plinth and further trimmed.Sometimes it is necessary to cut the 0.5 mm layer for perfect interfacing.
Sources:
  • how to make a right angle from the plinth

0
0