Tip 1: How to update the tile in the bathroom

Finish bath room with time become dull and unattractive.To improve the interior necessarily bring down the old tile from the walls.To return bathroom attractive enough to use several ways to update it.
you need
  • - spatula;
  • - putty;
  • - Drill;
  • - a chisel;
  • - a hammer;
  • - level;
  • - Roulette;
  • - cleaner for tile;
  • - skin №100;
  • - acetone;
  • - vinegar;
  • - suture paint;
  • - sealant;
  • - glossy epoxy paint;
  • - masking tape;
  • - dust mask;
  • - gloves;
  • - Points;
  • - knife;
  • - cloths;
  • - brush.
Guide
1
Select the method remontaObnovit tile in the bathroom room in several ways: to replace the damaged items close tile other material, update or seams decorate the walls with decorative panels.Stay on the option that is most appropriate for you at this time.
2
Update seams between plitamiUluchshit state joints are different ways: paint marker, suture use paints or apply new grout.Use markers and paints involves the temporary update tiles.If you are satisfied with the option of pre-use de
tergent and a stiff brush to clean the joints from dirt.If you have a bluish or black spots further treat them with a weak solution of vinegar.Thoroughly rinse the surface with water and dry.Use colors - they are suitable to work with seams of different widths.Pick the right shade and apply the paint on the gaps between the tiles.
3
Replace the old grout, if the use of cleaning products has not brought the desired result.First, use a scraper or spatula crumble at least half of the suture layer.Sweep brush crumbs and dust fill the seams with fresh mixture.Remove excess with a damp sponge tile, wait until completely dry and wipe the surface with a clean cloth.
4
Replace broken tiles If the damage is finishing slightly, cracked tiles must be replaced.In order to facilitate their detachment from the wall near the crack, drill a few holes.In order not to damage the good masonry, tile, remove in part by a chisel and a hammer.Prepare the surface, which scrape the old adhesive solution and estimates brush dust from places where there is no lining.Restoring the finish, be sure that all the tiles are on the same level.A day later, fill the joints with fresh grouts and dry surface.
5
Color tile pattern Update boring wall without changing the tiles.If you remove from its surface a brilliant enamel tiles can be painted monochromatic paint or apply any pattern.Using sandpaper sand the tile.Treat it with acetone to remove oil and debris.Prime the surface, let it dry for at least 3 hours and apply epoxy paint.
6
make decorative otdelkuSamy fastest way to update the finish - it's close wall room bathroom plastic panels.They are resistant to high humidity and kept contact with the water.It is possible to assemble a panel of several panels.Set on a wall mural - a large photo, made on plastic.Take a bath combination trim : mural - the central wall, and the rest - decorative panels.For a harmonious perception of interior bathroom consider the combination of basic colors photos and decorative panels.

Tip 2: How to update the old tiles

Eventually ceramic tile loses its beautiful appearance.A reason for this could serve as improper care of a tile or a long period of operation.When you can not put new tile , you can try to update the old one.
How to update the old tiles
you need
  • - cleaner tiles;
  • - vinegar;
  • - rigid sponge or brush;
  • - special marker;
  • - paint for tile joints.
Guide
1
To begin, clean the old tiles from contamination.Change the look of tile may be due to the presence of dirt on it.For example, traces of spatter and smoke can drastically change her appearance.Use strong detergents on the basis of the acid.Read the instructions before using the tool, or strong substances can damage the surface of the tiles.
2
Leave the vehicle on a hot plate for about ten minutes to make it react.Especially rub dirty places with a stiff brush.Then rinse with plenty of water cleaner.If after cleaning the lost luster tiles, wipe the surface with a solution of vinegar.
3
update the look of tile joints also.Remove the old grout and apply a new one.Before you start updating, clean the tile joints.Use a spray that is able to remove dirt and grease from the joints.It is simple.Apply the spray to the seam, leave for a few minutes, then rinse with water.If there are signs of fungus tiles, use in the processing of a solution of vinegar.Only after the complete drying of the tiles you are ready to upgrade.
4
to simply update the seams, use a special spray paint.Just click on the tip, let the paint accumulated, and then use it as a normal marker.This marker is designed for four millimeters wide seams.If mezhplitochny wider seam, then spend a few parallel lines.One negative of such markers - they are available only in white color.
5
If you do not fit the white color on the seam, the seam using paint.They are available in different colors, so choose the color of the tiles it is very easy.Also, these dyes can be used for any seams of the tile width.
Note
a tile need to constantly ensure that it did not reach the unsightly condition.
Helpful Hint
If you decide to upgrade the tile, then it is advisable to do it in the bathroom and in the toilet.Otherwise the tiles will be different from each other not only a picture, but its novelty.
Note
Before painting the tiles do not use a hair dryer to dry - this may be a cause of dust on the primed surface.
Helpful Hint
Deal sealant joints between the tiles - this will help avoid browning when exposed to moisture.
Sources:
  • how to update the old tiles

0
0