Tip 1: How to attach the plastic linings

plastic lining gives the opportunity to easily decorate a room, paying no attention to its functional accessory.It is used as a day of domestic work, and for the finishing of balconies and loggias.A particular advantage of the material in the simplicity of its installation - cope with it even the person who has no experience in construction work.
you need
  • - wooden slats;
  • - staple gun;
  • - staples;
  • - Saw;
  • - screws;
  • - drill.
Guide
1
Before you attach the plastic linings , you must create a frame.In principle, it is not forbidden to stick liquid nails directly to the wall, but this is possible only when the surface is perfectly smooth.Most often, this is possible only in finishing gypsum board walls.In a typical construction of prefabricated houses, even the walls have their flaws, and wall paneling just will not hold.The framework also allows to align and simplify the mounting surface.
2
to create furring screws to attach the entire surface of the wall thickness of a rail horizo
ntally.The distance between the laths should be within 0.5 meters.This will allow the crate securely attach bunk .
3
mount plastic lining can be nailed with large caps, screws or special brackets.The latter method is the most simple and saves a lot of time, since the protrusion clamping plate is narrow, and consolidate it with screws and nails are not too comfortable.
4
Measure the desired height of the panel and cut it saw or a hacksaw with fine teeth.In order not to injure a hand during operation of the cut edge, it can be treated with fine sandpaper, which aligns all the irregularities.
5
Insert the first panel in the strip or starting corner and fasten the edge with the help of staples in places where the edge is in contact with the carcass rail.In fact, it turns out that each panel is mounted in the 5-6 places.Then insert the available slots in the next bunk and secure it with the same method.Since the panel can be mounted not only on a wall but also on the ceiling.

Tip 2: How to fix the battens

Scope wooden lining has a wide range - for example, decorative trim various surfaces during repair, ceilings and walls lined up lining the balconies and loggias in urban flats.Besides, it's nice to go into the room fresh bath or sauna, which is studded with pine paneling, which comes from the wood flavor.Pergolas, summer patios and kitchens in the country - all this stuff is a must.
How to fix the battens
you need
  • - wooden slats;
  • - dowels and screws for wood;
  • - punch;
  • - thin nvozdi with small caps;
  • - plinth;
  • - protective compounds;
  • - the level and plumb.
Guide
1
Make on the wall surface crate to take this wooden slats and attach them to her.This takes into account if the lining is mounted vertically, then they should be mounted horizontally, or vice versa.The distance between the laths should be 0.5-1 meter.Elements crates should also be located in one plane, for this, use a plumb, level and wooden lining.If it is impossible to level the wall, grab rails and find the most protruding position.Then, set the level it horizontally and vertically.Secure with dowels and screws for wood.
2
Take-foot level and attach to the rail.Mark the point on the ceiling.Include in this place and the level of the second rail, align it with the previous one, for this or backing sheet under it, or remove the excess plaster from the wall.Maybe even have a plane skived superfluous wood with slats.Set the third rail on the two previous ones.
3
Nail the first panel lining in the corner.To attach it to the sheathing nails, use a thin (20 mm) with small caps, otherwise the wood may split.Drive the nails or in the middle of the board to be durable, or to preserve the appearance - in the grooves.In addition, you can apply a special mounting bracket.The next panel lining inserted into the slot of the previous and thus the "dial" the wall.Bottom and top nail decorative moldings.
4
Coat the surface of the wood protection composition.In addition, you can cover the ceiling and walls with varnish (nitrocellulose lacquer in rooms not used).Retail chains now offer environmentally friendly, waterborne alkyd and protective compounds.Depending on the choice of treated wood can be glossy or matte.Wall paneling room may be arranged in any direction, even diagonally.In narrow rooms will approach the horizontal, so visually it will be lower and wider.Installing the panels vertically will provide an opportunity to make the room "above".If you need to take a diagonal sheathing material reserve, also it is more expensive and more complex installation.
Helpful Hint
most difficult to insert the latest finish battens in the bar, so the easiest way to put it right corner, and then just insert battens into the slots.In fact, it will be held on the mounting bracket of the previous panel and rest against the wall.

0
0