- plastic panel;
Before starting work, be sure to read the installation instructions.Be sure to follow it, only then the result will be perfect.In addition, the panel before applying it is necessary to sustain at least 30 minutes for this must be disassembled and put a bunch of them individually.Just for this time, and you will have time to read the instructions carefully.
Then prepare the surface (wall) panels to be glued.Align them optional, needed a little trim only, if there is really very obvious bumps on the surface.The main thing you need to do - to clean the wall of dust, dirt and construction debris.If they are on the wallpaper, it is required to remove the
m.Remove tiles or painting is not necessary.The only condition - that was better coupling between the wall and the plastic, they need to be sanded.
now prepare itself to gluing panels.To do this, carefully cut them with a hacksaw, handsaw or a construction knife.The ideal saw for cutting a plastic - one which has 15 teeth.And do not forget about the fact that the panel should be cut only face up.The same rule applies to the drilling of plastic.
Experts recommend: do not immediately remove the protective film.Leave it in the plastic as long as possible.After all, such a measure will prevent the panel from damage in the process of cutting and drilling, as well as give them not contaminated.After preparing the cover, start to apply the adhesive.This should be thin and flat strips in a grid.The main thing is do not leave blank spaces.
Once, paste the wall panel, and at regular intervals its Screw the screws to the wall for additional strengthening.The works in this case, to carry out very carefully.Do not hammer in soft plastic anything, otherwise it can easily crack and have to start all over again.As you mount the panel in the bathroom, it is necessary to take into account the specifics of the room.For example, the distance between the plastic and the battery-heated towel rail should be at least 3-4 cm. At the same time all the objects that emit heat, should not be heated above 60 degrees Celsius.Once the panels are attached to the wall, carefully seal the joints with putty and paint the building.All bath ready.
Tip 2: How to polish plastic
Polymer clay in the hands of a resourceful crank can take many forms.The most popular are ornaments made of it, a variety of accessories that perfectly diluted common decorating background.Plastic - malleable thing, until he froze.Any flaw harvesting contributes to the appearance of rough surfaces that are not very pleasant to the touch.What to do if you have spent a lot of time in the production of jewelry made of plastic, and they turned not as smooth as we would like?
Grind your product.Place the blank in water for 10-15 minutes.Pick emery cloth, which is marked authorizing its use in water.Rub the product without removing it from the water.Long rubbing in one place does not need plastic - something gentle scratches are formed in the two accounts.Circular motion and constant change of skin to help get rid of any irregularities on the surface of the product.
If you have a need to polish the small details, such as beads, use the polishing units, which are used in manicure.
Use special fluid grinding - they are usually sold in stores and spares are called "polish."Preference is given to materials with a waxy component, they last longer on the surface.Add this mixture to the lined plastic surface and rub with light circular movements.The composition of the fill surface microcracks and give a nice shine.However, serious scratch these compounds, of course, will not hide.
For large surfaces fit foam sheets, which are polished car body.To find them is not difficult, in any specialty store, you can buy them at a reasonable price.For the convenience of take Polishing Machine and measure the size of her head, which was previously clear.By the standards of the disk cut from foam and stick it on the car.Start the machine and walk across the surface of the plastic, pay attention to the fact that the foam does not come loose, otherwise instead of glitter you get a scratch.
In industrial environments using grinding and calibrating machines.They are often treated wood, but they do an excellent job with the plastic and plexiglass.
Our ancestors were ground any decoration using the carpet.Who knows, it may be plastic, which firmly rubbed on the old carpet sparkle with a new luster.