Tip 1: How to insert a window frame

windows in the wooden house creates a complete image of the structure.Their main set in compliance with the technological features of these buildings.Windows not only disturb the harmony of wooden houses, but also relieve the owners for a long time on their repair.You can use the services of professionals, and you can do it and in the home.
you need
  • - Edged board;
  • - bar;
  • - mounting brackets;
  • - levels: water and construction;
  • - a plumb;
  • - screws;
  • - foam.
Guide
1
Remove the window sash.To do this, remove the pins from the hinges.This will simplify the work process and facilitate tilting of the window.Prepare okosyachku.You can use the option of laying bar.To do this, prepare a timber the size of 50h50mm, install it in a pre-cut groove, thus he will guide the vertical movement log .Okosyachku collect from edging board size or 50h150 mm or 50x200 mm.It all depends on the thickness of log .This method is the most important.Secure in the side windows slide mounting brackets, three on
each side.
2
Put the box on the chips (about 2 cm) in the bottom of the opening and adjust the level horizontally.It is best to use water.This will give the most accurate measurements.After alignment, leave the bottom of almost 2 cm gap for the foam.Then, align the screen vertically to the sash closed correctly.To do this, use a plumb and level building.
3
Attach window to okosyachke screws through the mounting brackets.Try not to get into the ridge beam, on which it is fixed.Screws best twist angle, thereby "firmly" attached to the structure okosyachki frame, depriving it of mobility.
4
Install window sash.They should be hanged on the window until foaming to foam frame is not deformed.If the technology in the installation of plastic window frame was observed, okosyachka delivered smoothly, on the sides of the window frame to remain okosyachki about 2cm away to foam.Top clearance to the timber will be 5-10 cm. It is necessary to shrinkage log , when the wood is completely dry, there was no pressure on the window.
5
Spend verification.For this purpose, fixed zapenennuyu not put the sash window.Open them in half.In the case where they do not try to open up further to close, or vice versa, the installation is made properly.Then zapente frame construction with foam.

Tip 2: How to install windows in the frame

integral attribute in the construction of homes are window , which can be made of wood, metal structures and different kinds of polymers.Despite the fact that the installation process window in a wooden house seems simple, it can bring a lot of grief if you do not take into account certain patterns when working with wood products.The principle here is one, and it does not matter from which the house is assembled from logs or lumber.And in both cases, placed in the window opening of the casing block.
How to install windows in the frame
you need
  • - timber 50mm;
  • - Edged board;
  • - gon;
  • - a plumb;
  • - Chain Saw;
  • - foam;
  • - nails.
Guide
1
Mark the window opening with a plumb line.In this case, a simple construction is not quite level.
2
for cutting the window opening is better to use a chain saw, which is now in specialty shops large selection.Cut the size saw an opening so that the hole captured not less than half of the top and bottom of the log in the blockhouse .
3
Using a chain or circular saw, router or better yet, choose a groove width of 50 mm and a depth of 50mm in the end wall.Chisel and chisel manually strip the ends of the groove and nail bar on 50mm.It is important to take into account the moisture content of the framework.Whether it is the fresh carcass or have constant-stranded.If you have made from fresh log of wood, the length of the bar should be at least 5cm long groove.If the log-stranded 2cm.
4
Take wide board, width 50mm and nail to the bar .Shirina board must comply with the thickness of the beam in blockhouse .
5
the upper and lower thrust in a log nail boards that form the window opening.Better for this use special nails which then drowned and holes can be treated with putty.
6
for the accuracy of determining the angles, the installation of a window box, use square.
7
Install window on the mounting foam.Using cladding boards, close the window from the outside on the perimeter.Inside seal the layout.
8
window aperture obsheyte board.The board nailed only to the lower log, so it does not create obstacles to the shrinkage of the framework.
9
Window mounted on screws and mounting foam.The mounting foam is best to choose with regard to weather conditions.Keep in mind that ultra-violet rays have a devastating effect on the mounting foam.
10
All wooden components necessarily impregnated with an antiseptic, which is sold in a wide range of DIY stores.In keeping with this technology and of the installation of windows in the frame, you will cope with this seemingly daunting task.
Note
Note humidity framework.If necessary, give him time to settle.
Use only high-quality, dry timber.
Helpful Hint
Bar and choose a board of coniferous trees.

0
0