Tip 1: How to polish bath

increasingly popular today are acrylic baths - they are easier to install, easier to cast iron or steel, are available in a huge range of different shapes and sizes.There are drawbacks, chief among them - the fragility from falling into the bath heavy object may form a crack, then tub can not be repaired.However, acrylic bath is easy to care for, to remove minor injuries, self-polishing.
you need
  • - detergent;
  • - polishing wax;
  • - silver polish, toothpaste;
  • - vinegar or lemon juice;
  • - spray for chrome-plated surfaces;
  • - fine sandpaper, abrasive polish;
  • - sponge cloth of a soft cloth, sponge.
Guide
1
Clean and polish acrylic bath: Clean with a sponge soaked in water with a little detergent.Do not use detergent containing abrasive components, alcohol, formic acid (formaldehyde) or ammonia.The use of such detergents or detergent and cleaning baths without water leads to fogging of the surface.
2
Apply detergent evenly over the entire surface, leave the bath in this state for 5-10
minutes, then wipe with a sponge and rinse with water.Repeat case of severe contamination.
3
Apply wax polish on the surface of the bath and gently rub with a cloth of soft tissue.
4
remove stubborn stains using a liquid detergent, silver polish or toothpaste: put them on a cloth of a soft cloth and rub the stain.
5
remove encrustations from the surface of the bath using lemon juice or vinegar.Dampen a cloth of soft tissue in hot vinegar or lemon juice and rub the stain.
6
Spray spray on chrome surfaces directly on the chrome bath, rinse with strong stream of water (in the case of severe pollution means leave on the surface for 5 minutes), wipe dry sponge.
7
Polish the hot tub acrylic Fill it with warm water, dissolve in water, liquid detergent, run the hot setting for five minutes.Turn off the system and leave the hot water bath for 10 minutes, then drain the water.
8
Fill the water hot tub again and turn on the whirlpool for 5 minutes, then drain the water, clean and polish as usual bath of acrylic.
9
remove small scratches on the surface of acrylic baths: bath wash, gently rub the scratch with fine sandpaper, then polish abrasive, in the last instance, apply and rub wax polish.

Tip 2: How to polish metal

Polishing metal used to improve the surface cleanliness of devices, components, eliminating them on different tracks of the previous processing (scratches, strokes, tiny bumps and small dents).There are two types of polishing: preliminary and final.To mechanically remove the irregularities on the surface of unfixed preliminary polishing abrasives used.The final polishing is carried out by small grinding powders.
How to polish metal
Guide
1
Metal can be polished with special polishing pastes, which includes in its composition chalk, limestone, tripoli, dolomite, chromium oxide, aluminum oxide and iron oxide.
2
In this case the surface of the fine finishes reach friction piece of woolen cloth or felt, lubricated with a special paste.After polishing the surface will acquire such luster.
3
To prepare the paste for polishing metal, take the wax 20 g, 10 g of stearin, technical fat and 3 grams of micropowder M 50 - 67, all the ingredients, mix until homogenous.
4
polished metal can also chemically, that is the subject of a simple immersion in a bath with a special polishing solution without the use of electric current.You can use the china cups and trays.
5
To prepare a polishing solution, take 350 ml of concentrated phosphoric acid, 50 ml of concentrated nitric acid, 100 ml of sulfuric acid and concentrated sulfuric acid and 0.5 g of copper nitrate.All the mix.
6
Working temperature of the bath should be 100-110 ° C. By the time you need to polish from 0.5 to 4 minutes.When polishing will be allocated a pair of choking, so put a bath in a fume hood or outdoors.
7
If you need to polish some inaccessible metal surfaces, especially on small jewelry, then perform polishing sticks of wood (linden, birch, aspen).Sticks cut a shape that is suitable to the treated surfaces with a cylindrical, rectangular, triangular cross-section, with the concave and convex working part.This part of the rub sticks cooked pasta.
8
for polishing metal surfaces of large sizes can use different forms of wooden blocks, pre-pasted out the inside of the skin.
Sources:
  • Care acrylic bathtub
  • polished acrylic baths

0
0