Tip 1: How to build a canopy of polycarbonate

Polycarbonate is a modern material that is often used for the manufacture of awnings .He has a number of advantages: an attractive appearance, light weight, the choice of color.Despite the fact that many companies offer to carry out installation of the canopy polycarbonate for a fee, this work can be done independently.
you need
  • - polycarbonate sheet;
  • - metal tubes;
  • - wooden slats;
  • - paint;
  • - screws;
  • - fasteners for polycarbonate;
  • - Drill;
  • - hacksaw.
Guide
1
before a canopy, perform measurements and buy the necessary ingredients: self polycarbonate tube battens, fasteners.
2
To attach the canopy frame is required, the amount of which depends on the available free space.The form of the canopy depends only on personal preference, since polycarbonate is flexible enough to take the form of a semicircle.
3
Take 4 tubes and dug them into the ground to a depth of 30-40 cm, forming a square or rectangle.Between the pipes should be a distance of about 1-1.5 meters, if the
canopy of polycarbonate will be larger, the number of poles increases.They will be the basis for the canopy frame.If you want to achieve high reliability design, cement the base of the pipe.
4
from wood make the frame, and looks like a window frame whose sides are equal in size to the distance between the pipes.Inside the frame should be several transverse slats arranged at a distance of 50 cm from each other.It will be attached to them polycarbonate.Treated wood stain or paint it to the frame longer keep in shape.
5
With over with existing technical holes, attach the wooden frame to the pipes.On the corners of the tube are attached with screws on metal.On the wooden part, you can use any screws.
6
Cut a circular saw or a hacksaw piece polycarbonate , the amount of which should be 5-7 cm wider than the established framework.
7
Place the sheet on the frame and drill holes in it for fixing.They can be positioned at a distance of 50 cm from each other.Drilling is preferably carried out at high speed drill initially, otherwise the edge of the hole getting ripped.
8
with screws and special washers with wide hats, attach a sheet to a wooden frame.Avoid leaks in the attachment points is possible by means of rubber gaskets.To the edge of the canopy looked more carefully, it is necessary to put them on a special finishing profiles, which are sold in the same stores as polycarbonate.

Tip 2: How to fix polycarbonate

Recently, much attention was paid to securing polycarbonate .This material has many good features, but also has a refined appearance.Construction of polycarbonate used everywhere.Of course, if the polycarbonate has a modest size, it is possible to mount it on the appropriate sized sections.However unlikely in this case to take into account all the nuances of behavior sheet cellular material.
How to fix polycarbonate
Guide
1
have cellular polycarbonate very sensitive area.It can deteriorate under the influence of mechanical stress.Therefore mount produced without removing the protective film on both sides of the sheet.When installing polycarbonate prohibited him too much clamping, because there will be no natural thermal expansion.This adversely affects the design itself.
2
necessarily make insulation from moisture, dust and insects in the open ends of the sheet.For this purpose, polycarbonate paste special tape ends.It is also often put on the closing profiles to protect the tape from damage.The lower profile make holes.They are necessary to ensure air circulation.Thus, within the channels will not condense water vapor.The upper end of the sheet carefully closed.
3
This material absorbs moisture from the atmosphere.If it will occur reduction in the relative humidity inside the channels of the sheet condensation.This condensate is difficult to remove the assembled structure.Before assembling producing material is maintained for several days in a dry room.Thereafter, the ends are sealed by self-adhesive aluminum tape.If condensate has appeared, then you can remove it only by blowing compressed air voids.
4
Roofs of cellular polycarbonate always designed with a slope of about 90 mm / m.This is done in order to ensure that rainwater.
Sources:
  • Fastening products from polycarbonate
  • polycarbonate how to fix

0
0