Tip 1: How to unfreeze the pipe

winter, the water in the pipes often freeze.A few reasons for this: it is the lack of depth of the pipe, and ineffective insulation, and low water consumption and a very low temperature.Those tubes, which you have easy access, easy to defrost with a hair dryer.And what to do with pipes that are laid under the ground?
Guide
1
If the water we froze on the input - it's not so bad.In this case, the wall can be heated.And if the ice "plug" is on, then there is a serious problem.In order not to wait for the spring thaw when the pipes themselves can use one of our advice.
2
Metal pipes unfreeze easy.We need a welding machine, which must be connected to both ends of the pipe.In this way, the problem is solved for a couple of hours.With plastic pipes the situation is different.The current they do not spend, so the welding machine to solve the problem fail.
3
For the first method, we need Hardened steel wire with a diameter of 2-4 mm, gidrouroven building, and enema.Aligns the wire and tube
level, connect them together with electrical tape.The other end is connected to the level of an enema.Wire tube slips into the tube up to the place of freezing pipes.Domestic hot water, pour into the tube.And that we are not flooded with cold water, substitute a bucket under the pipe, as the hot water displaces the cold in the same quantities.As the ice melts the tube to move forward.The slow method, but effective.
4
But the second way is quite original.Take the copper twisted pair wire, plug usual for the outlet.If the pipe length of 30 meters, it is recommended to buy a pump or compressor for sucking the cold water.
5
Remove to wire the top layer of insulation, one core laid bare, and the second Bends along the wire in the opposite direction.We are making a bare living 3-4 turns and unnecessary bites.Then back down 2-3 mm from the turns and twists turns of the second conductor, connect a wire to the fork and our machine is ready.He will provide us with water heating from the wire when we turn on the power plug.Thus our plastic pipe will not melt, but only heated to ice and water.
6
can try the device in a basin of water.From the end of the instrument should be based on bubbles and buzz.Do not put your hands into the water, and then the "zhakhnet."Now we put the wire into the tube and push it until it stops.Now we turn the device into a network and just pushes the wire stared straight into the ice.Melted the ice as 1-1.5 meters, pump out any excess water from the compressor or pump.Otherwise, the tube can again be nipped by the frost, as long as we continue to push through the wire.In addition, the speed of our work will increase markedly if the device does not need to be warm but ice is also a liter of water in the pipe.

Tip 2: How to unfreeze the composition pipe

winter, in private homes often freeze in the coolant pipes and water heating.Metal pipes are less susceptible to freezing, but still likely to get into this bad situation there.And this phenomenon should be approached very seriously, because it may lead to a fatal emergencies
How to unfreeze the composition pipe
Guide
1
When defrosting pipes required to follow certain rules, derogation from which can bedanger.Fully open the valve located closest to the point of freezing.Defrost is carried out slowly, gradually moving from the open gate to the place of freezing coolant and beyond.Constantly monitor the temperature of the pipe by hand.This should allow the temperature to touch the pipe without the risk of getting burned.Overheating of the pipe may lead to the formation of steam inside it, and further - to its rupture.
2
If there is a system of independent heating of the building, turning it on.When the house is fully warmed up, the pipe unfrozen themselves.This is the easiest and safest way to defrost.If the frozen pipe is located outside the home, for example, in the basement, Wrap a cloth and pour hot water.Under pipe put container to avoid spilling water and icing.
3
If you have warmers or electric blankets, wrap them around the pipe and plug it into the mains.Top nabroste any thermally insulating material.Heating power set minimum.Gradually increasing the heating power, smoothly move the heating pad or blanket in a direction from the open valve into place frozen until the end of the place of ice jams.
4
If there is a household hair dryer, heater fan or an infrared lamp heater, use them.To do this, place them so that heat generated from them, was sent to the place of coolant freezing in the pipe.Remember that plastic pipes can withstand temperatures of 120 degrees, so take care not to overheat them.If you use any electrical appliances for defrosting, make sure that the wiring in the basement is designed to power a little more than power included heaters.
5
Be extremely careful during defrosting pipes with a gas burner or a blowtorch.Firstly, whenever possible to use another method, do without the burner.Secondly, the burner must necessarily have a flame divider, and on the other side of the pipe must be heated sheet of asbestos board.Third, constantly monitor the temperature of the heat pipes and the plugs gradually.And fourth, do not leave the stove unattended, and keep a fire extinguisher handy.
Sources:
  • how to unfreeze water pipes

0
0