Tip 1: How to change the gasket in the mixer

trouble when in the kitchen or bathroom faucet flows.Constantly dripping water have a negative effect on the counter, which winds round the amount to the account of the owners of property.Flowing water can contribute to the appearance of unsightly stains on the surface of sanitary ware.
you need
  • - new gasket;
  • - wrench.
Guide
1
The most common cause is flowing tap wear pads.This is the most short-lived part in the mixer.The reason for this material - rubber deteriorates on contact with water.Even with a well-twisted the valve stem or the valve will leak out if the gasket is worn out.Repair the leak can only replace it.Shut off the water access to the faulty tap.Make sure the water does not come out (if it will ooze out a thin stream, it is permissible).
2
Remove the head of the crane - it is necessary to use a wrench.Remove the old gaskets and replace them with new ones.Gaskets can be purchased at the store or make your own from a simple rubber.Take the form to remove a lining.If
the old in a bad condition, try to determine the approximate size, measuring the first internal, then external diameter of the product.
3
Take a piece of rubber or leather.Circle size should be cut slightly larger than the slot at the valve.Insert the gasket in the makeshift nest.Leather piece suit in case saddlebag destroyed edge and simple rubber gasket may not fit tightly.The new gasket thickness should be at least 3.5 mm.The edges of the gasket is cut at an angle of 45 degrees - it will help to get rid of noise during operation of the crane.Manufacture of articles should fit snugly to the seat - and then the crane will operate quieter.
4
Such methods are changing pads are suitable only to repair the faucet with cold water.High temperatures has a devastating impact on the pads, which become brittle and unusable.To make a lining for the hot water tap, it is necessary to choose tires with a cord, which is more durable than a simple rubber or leather.

Tip 2: How to replace the gasket in the mixer

When in the kitchen or bathroom faucet drips, it introduces himself from even quite aged man.In addition, it is not the best way affects the state purse after payment of water bills.The problem often lies in the simple laying of rubber, which is easy to replace.
How to replace the gasket in the mixer
you need
  • - adjustable wrench;
  • - Screwdriver;
  • - a new gasket.
Guide
1
Shut off the water before starting work.With the mixer, remove the plastic handle - it is necessary to remove the cap from the plastic and unscrew the locking screw.Then you can get access to the thread of the valve crowns.In cross-section of the guide valve is often square, but there are also guides scored.They have not very nice feature - they can "take a strong liking" in the area of ​​the thread and remove the plastic part can be somewhat difficult.You can use force to remove it, but it should not be too zealous.
2
Remove using a wrench crown valve.It is possible to take advantage of this and pliers, but with their help, the crown can be unscrewed only with great effort, and the chipping, however, remains much.As a result, it should design department at the end of which a rubber or plastic gasket.It is attached with nuts and washers, there is another option - a pin with a thickening at the end.The old gasket should be removed.
3
Install the new gasket in place removed.To do this, buy it at the store or do it yourself.You can use a piece of rubber camera, old shoe soles or other wear-resistant rubber material, which with the help of a knife or scissors to cut the item should be the proper diameter.Do not forget to make a hole in the center of the notch and treat, if not turned out to perform all neatly.The gasket should produce as smooth as possible.
4
Place the gasket on the crown and lock it with the fastening element provided for in the design.Crown set back and tighten properly.Now replace the handle.Reconnect the water and check the operation of the mixer.
Helpful Hint
If you want to make yourself a lining, it is possible to determine the use of the old forms.Measure it, or simply attach to the material and draw a suitable pencil.If the old gaskets in poor condition and to remove the forms to use them does not work, you can make new, measure the diameter of the nut inside.
Note
spoiled by frequent contact with water seal is not able to provide full protection tap - water trickles out, even if the valve device is closed very well.Unpleasant sounds occurring during use of the crane, may also be due to the fact that the napkin is worn.
Helpful Hint
Do not hurry to make a complete replacement of the tap because of one little detail, even if the reserves are not found suitable gasket.You can choose to make this part.It is better to choose for this purpose rubber sheet, but you can optionally use even worn out heel on heel.Do not use foam rubber, soft plastic and uncomfortable.

0
0