Tip 1: How to cut an angle of 45 degrees

During the renovation or construction of uncommon situation when you need to make the junction of two parts so that it fit perfectly in the corner room.If it is necessary to cut off the angle in 45º, proceed in the following ways.
you need
  • - line;
  • - pencil, pen, marker;
  • - a sheet of paper;
  • - protractor;
  • - miter box;
  • - a knife, scissors, jig saw or other cutting tools.
Guide
1
If the surface of the material quite extensive and allows you to make notes, draw one of the lines cut with a ruler.Then draw the perpendicular to this line using angle nik or any object with smooth edges, for example, a sheet of paper or a book.
2
Ruler mark on each side of the angle equal segments, for example, 10 cm. Measure the distance between the data points and divide it in half.This point is connected with the top of the right angle.You got angle to 45º, are now cut material drafted on the lines with scissors, a knife, jigsaw, or other tools.
3
Select one of the lines cut, take a p
rotractor and attach to the line.Locate on a scale mark of 45º and connect this point with the center of the protractor.According to the planned lines, cut the material available tools.
4
paper, film, foil or other flexible material is easy to cut as follows: Find or draw a straight angle (for a sheet of paper is any of its corners).Fold the sheet so that the adjacent sides match.Cut the sheet along a fold line.
5
If you need to cut angle of 45 degrees a few times, for example, by fitting a plinth, make a template.To do this, take a thick cardboard, draw a square on it, and cut it diagonally.
6
In order to cut the material at an angle of 45º in large quantities, buy a miter box, this tool can easily be found in any hardware store.Include a plinth or rack inside so as to be located in the space, and cut it with a knife, jigsaw, or other tool.

Tip 2: How to cut skirting

plinth can be made of foam, plastic, wood or other materials.To cut a plinth smoothly and avoid damaging the floor, for each of the materials used must choose his instrument.
How to cut the plinth
you need
  • Two tools that will be needed in any case - a miter box and a pencil.Without them, cut off the plinth exactly is not easy.Sometimes it can be useful and clamp.
Guide
1
To cut made from foam ceiling moldings, you need to pick up a paint knife.Before you start, be sure to insert a new blade to be not only acute but also long enough.Place the miter box to the baseboard, and cut it with a painting knife to the desired angle.
2
If you face the task of cutting off a plastic plinth, you can safely cut his hacksaw.Small teeth of a hacksaw excellent job with the plastic, leaving it free of burrs and traces, allowing to achieve a smooth and precise cut.
3
Cutting wooden baseboards can use a hacksaw on wood with a fine tooth comb.Just as in other cases, the baseboard must first mark according to size, then place in the miter box and cut off at the desired angle.
4
Particular difficulties may arise when cutting baseboards made of wood or wood shavings with lacquered or veneered.The top layer of such products is extremely susceptible to mechanical stress, and to cut the baseboard without damaging the coating, it is necessary to try very much.In this case it is better to cut a hacksaw on wood with the fine-toothed or hacksaw.Since these skirting boards is also quite expensive, then before the desired cut blank is first workout.
Helpful Hint
lacquered plinth often do not allow tight lock bar in the miter box.In such cases, you can use a clamp to securely hold the plinth when cutting.
Note
not always make the corners of rooms exactly 90º, often they can be sharp or blunt.In this case, if you have already cut the baseboard or other material at an angle of 45º, stick it so, and seal the slot filler.
Helpful Hint
to the corners of the two parts, for example, precisely matched skirting, first cut off one of them at an angle of 45º, attach it to the place of repair here and try on the second part.Draw a line with a pencil and cut it cut angle (even if he is different from the set, but the design will fit perfectly into the space).
Sources:
  • how to make an angle of 45

0
0