Tip 1: How to glue wall panels

modern market of building materials is incredibly rich: it offers a huge range of all kinds of products.It is noticed that today is a special demand for wall panels.They give a complete view of the interior space.However, the increased interest in the decoration materials can be explained by the fact that the installation of wall panels does not require spetsznany: everyone can glue them.
you need
  • - heater;
  • - wall panels;
  • - bucket;
  • - Brush;
  • - water;
  • - spatula;
  • - primer;
  • - a plumb;
  • - drill with drill bits;
  • - screwdriver;
  • - hacksaw;
  • - hacksaw on wood;
  • - gon;
  • - pencil;
  • - screws;
  • - a hammer;
  • - Roulette;
  • - rails;
  • - insulation;
  • - Aluminium scotch;
  • - special glue.
Guide
1
Thoroughly warm up the room, the walls of which will be pasted wall panels.The minimum temperature in the room - 10 degrees above zero.
2
Unpack the wall panels and leave them for a few days in a heated room (note: the temperature should be above ten degrees).
3
Prepare the wall.This operation
is performed in two stages.First, remove with a spatula old wallpaper before moistened with water and giving a little swell.Second, prime with the wall.
4
If the walls are perfectly smooth, apply a special glue evenly on the first wall panel (let it soak), and then on the surface of the walls.No later than half an hour after applying the adhesive to attach the wall panel wall, gently press and smooth (top down and from the center of the panel to the edges).A method of bonding these panels (butt joint or overlapping) depends on the recommendations of the manufacturer of wall panels, which are set forth in the instructions accompanying the product.
5
If the wall surface is uneven and has a lot of damage and defects before gluing wall panels, set the crate.Remember, the crate should be placed perpendicular to the panels.Using screws, attach reechki batten to the wall.The distance between reshetochki should be 600 mm: at too great a distance to press any strong wall panel may damage it.On the side of the heater nefolgirovannuyu apply a thin layer of glue and glue it and then seal the joints insulation aluminum tape.
6
Then install framing accessories (angles and profiles), and only then stick wall panels.

Tip 2: How to glue the plate to the wall

choosing frameless method of fixing plasterboard panels, you can align the walls as quickly as possible, without creating a special crates.To glue the plasterboard panel to wall , eliminate irregularities of the walls, and then attach the panel adhesive plaster or mass.
As the glue to the wall panel
you need
  • - hammer,
  • - screwdriver,
  • - spatula,
  • - carpenter's knife,
  • - cutter slabs of drywall,
  • - hacksaw,
  • - building level,
  • - pencil,
  • - special glue or plaster mass.
Guide
1
Get the required number of sheets of drywall, calculating it according to the surface area of ​​the walls that you need to coat.Rate surface irregularities walls of the room, as the choice of method depends on the finish of this indicator.With significant drops in the level of the walls, choose to fix a lot of plaster panels use a special frame for mounting.
2
If you want to paste over gypsum panels reinforced concrete walls or walls of the building, built of large blocks, put on a sheet of drywall with a notched trowel plaster mass distributing it throughout the long, thin strips.In places where the plasterboard panels are attached to the door and window openings should be covered with a mixture of the inside of the panel completely.
3
Put the plasterboard panel to wall , using a wooden lining and leaving the distance to the floor about ten millimeters.Within ten minutes after application of gypsum panels, gypsum mass or when the glue has not yet grappled with a finished room wall, align the position of the panel using a spirit level or plumb.To save time and used solution and sticking a plaster panel to wall as quickly as possible, try out a batch of gypsum mixture immediately mount, at least three sheets of drywall, firmly sticking to the walls of your room.
4
between gypsum panels are mounted vertically on the sides is required to leave a small gap of about five to seven millimeters in a few days are the usual fill the gap with putty.After mounting the panels and complete drying of the adhesive used or gypsum mass left over from the wooden lining carefully fill in the gaps with mineral wool or high-quality acrylic sealant.
5
In the case of significant irregularities of the walls of your room, use fixing panels gypsum mass, causing the mixture in large quantities - not thin strips and piles and distributing them throughout the panel, leaving only nezamazannymi edge.To plaster panel mounted smoothly, press down each panel to wall after labels and check the level.
Note
adhesive is applied over the entire surface of the wall panels, otherwise these "plitochki" not glued well enough.
Helpful Hint
spots of adhesive can be removed with a knife, and then clean them lightly moistened sponge.
Sources:
  • installation of wall panels PVC and MDF

0
0