Tip 1: How to tie two hooks

The ability to tie hooks - it is one of the basic skills that every angler should own.It begins with this training beginners as well-assembled gear is the key to successful fishing.
you need
  • keska, hooks, leashes of different length, a carbine.
Guide
1
Take one of fishing hooks and pull the line through the eye of his leash.
2
Form a large loop of fishing line along the forearm.
3
Wrap the end of the fishing line around the inside of the forearm loop several times.You get a universal unit, which is used by fishermen for accession hook to the line.In addition, there are several other components that are often used for joining hooks to the line.
4
The same way, attach the hook to the other second leash.
5
Connect the line to a dull snap hub.Using a carabiner, you avoid the possibility that one of the leashes will cut the line.
6
Attach the leash to the first free ringlet carbine swivel hinge.
7
Do the same with a second leash.

Tip 2: How to tie a hook to the bait

Each angler must know how to tie a hook , to the node of the fishing line does not untie when wet, and the line was not broke off under load.There are many different nodes.Consider the simplest.
How to tie a hook to the bait
Guide
1
Take the length of fishing line, fold it in a very simple loop and put on the shank of the hook so that the loop looked toward hooking.The fore-end and the line, which is folded in half, press the fingers of his left hand.Take your right hand at the short end of the fishing line and wrap the line with forearm 2 - 3 times.
2
right hand intercept windings, do the end of the line has three turns.Hold the turns, thread into a loop free end of line and pull the main line.In this way hook is firmly attached, and his forearm will be a continuation of line, and this is very important when cutting.
3
To snap hooks larger fifth issue, it is necessary to make a ball on the line.To do this, the line of alcohol lamp heat to melt and it turned out to be the end of the bead - droplet.Then apply the line on the shank of the hook, to get the ball to the hooking and wrap Soie (derived from the nylon cord).
4
Fix the coil on the shank universal glue.If you want to hook a binding forearm had thickening of the end of the fishing line, where the turned winding process the file or knife.
If you got a hook , and on the shank spatula, not a ring, do not fret.Such hooks attached to a fishing line just as well.But in order that the line does not cut the side edges of the blade, previously under the spatula tie 2-3 turns sewing thread.
5
If you want to do vosmerochny simple knot at the end of line anchor make a simple loop and pass it an end of line one more time.Then expand the loop so as to obtain the eight in her forearm insert the hook, tighten the knot on the ends.To get vosmerochny double knot, the end of the fishing line skip in the loop twice.Forend hook embrace of lay and fasten the ends.
Note
Do not use iron hooks, experts advise to use copper devices.The fact that iron hooks rust rapidly on contact with water, which is inevitable.As a result, the fishing line wears out and loses its strength, it may break at the crucial moment.The most convenient is the catchy hooks that allow you to quickly remove the leash with prey in deep swallowed hook fish.
Helpful Hint
In this case, you must use the leashes of different length, otherwise they will be constantly confused, greatly complicate the process of fishing.As a rule, applied leashes length of 5-7 and 10-15 centimeters.The diameter used the leash must be smaller than the diameter of the main line.By the way, it will give you another advantage: the fish that gather to eat the bait, the thinner monofilament alerted smaller and therefore you are more likely to take hold "trophy."
Sources:
  • Shown here are the most common components that are used by fishermen to tie the hook to the line.

0
0