Tip 1: How to install an ultrasonic parking sensor

ultrasonic parking sensor is very convenient for those who have not yet learned how to skillfully park.With it, you can learn about the interior of the invisible barriers, high curbs and other dangers your car while reversing.
you need
  • - ultrasonic parking sensor with a set of fasteners;- Tape or tape measure;- Marker;- Masking tape;- An awl;- Drill;- Duct tape.
Guide
1
Wash the car, or at least a bumper and prepare the space.It is best to install the sensor in a comfortable garage, to be able to accurately calculate the height from the ground.
2
Remove the battery from the negative terminal and disassemble the inner interior of the vehicle.Think where will be more convenient to install parking sensors - on the rear window of the car or on the control panel.There are also parking in which the information is displayed directly on the obstacles on the windshield.In addition, you must immediately determine how wiring will be laid from the sensors will be located where the main unit
of the parking system.
3
Bumper Cover the masking tape to avoid damaging the coating.Choose a starting point - for example, the edge of the bumper or symmetrical parts.Or you can spend the layout marker - it is washed away from the surface without damaging the paint.
4
Spend markings on the bumper of the car.Please note, some car models markup provided by the manufacturer.To perform manual partitioning, you need to carefully read the instructions.The sensors should be placed at the same height (typically about 60 cm from the ground) and horizontally.From the correctness of marking will depend on the accuracy of the data sent by the sensor, as well as the existence of "white" areas where the obstacles are not visible.
5
If the model PDC provides pass-through installation, put in place the point marked with an awl.At this point, drill holes using a drill and install the parking sensors.
6
Pull the wiring through the rubber plug in the trunk.Weave wire together, but leave a small loop that if necessary can be easily replaced by one of the sensors.Install the unit in a corner of the trunk, and then test the system.
7
If the system works, fix the current system and the display unit at the selected location, route and insulate wiring.Easy to install wireless Parktronic, since there is no need to pull the wires through the interior.

Tip 2: How to install an ultrasonic sensor parking sensors

parking cut into the front or rear bumper and serve to facilitate reversing or performing various maneuvers.When selecting parking radar note the manufacturers.Better if it will be a well-known brand (ParkMaster, Sho-me), which is made with high quality and will not give failures.
How to install an ultrasonic parking sensor
you need
  • - Drill;
  • - Screwdriver;
  • - electrical tape;
  • - sided adhesive tape;
  • - Tester;
  • - Roulette.
Guide
1
Purchase a set of parking sensors. sensors , which cut into the bumper, come in two colors - silver and black.If the bumper of your car a different color, set the black sensors that then can be painted with paint from spray.Complete sets for installation are with 4 or 8 sensors.To install sensors in the rear bumper only, select a set of 4 sensors.
2
mark a line on the bumper of the sensors.Use a tape measure and measure around the edges by 15 cm. From this mark, measure an equal distance to the sensor.Measure the distance from the earth in 55-65 cm to the planned lines.The line of intersection will be a place where you need to drill holes.
3
The resulting hole, insert and secure the sensor, pull the wire into the trunk through the rubber plug.In her absence, drill a small hole in the trunk.
4
Install the control unit in the trunk.It is better to attach it with tape bilateral side of the metal surface.Connect the power supply unit, connecting the red wire to the backlight reverse, and black - to ground.
5
Car mount monitor.Monitors come in different versions: oval, rectangular, built into the rearview mirror.Place the monitor in the center of the dash at the glass and secure with double-sided tape.
6
Wires from the monitor, slide down through the dashboard, on the side racks and threshold (after they dismantled).If necessary, the wires can be extended.
7
Under torpedo near the pedals get the vehicle wiring harness staff.Need wires responsible for the brake pedal and the ignition.To find them, use the tester.TO GROW wires found additional wires and pull them into the trunk of parsed doorstep.Connect them to the power circuit according to the PDC.

0
0